Dalam Stok Produk Hangat
UHLAC1
UHLAC1 HLAC1 HL-AC1 PANASONIC HL-T1 sensor controller, NPN, 12-24VDC
$0.00USD
3192 dalam stok
Spesifikasi Utama
Barang:Specifications
Jenis:NPN output
Berat:Net weight: 140 g approx.
Butiran:Controller (NPN output)
Maklumat Pembekal
PANASONIC
Produk: 4316
Biasanya dihantar dalam 2-3 hari bekerja
Kualiti Dijamin
Penghantaran Pantas
Sokongan Teknikal
Spesifikasi Teknikal
| Parameter | Nilai |
|---|---|
| Barang | Specifications |
| Jenis | NPN output |
| Berat | Net weight: 140 g approx. |
| Butiran | Controller (NPN output) |
| Produk | Ultra-compact Laser Collimated Beam Sensor |
| Bahan | Enclosure: Polybutylene terephthalateTransparent cover: Polycarbonate |
| Kabel I/O | 0.09 mm210-core composite cable, 2 m6.562 ftlong |
| Nombor Bahagian | HL-AC1 |
| Tetapkan semula input | 0 V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Nama produk | Ultra-compact Laser Collimated Beam Sensor HL-T1 |
| Input masa | 0 V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Output linear | Current / voltage output switchable (Note)-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller. |
| Fungsi utama | ・Measured value display・Setting value, light amount value resolution display・Standard received light setting・Automatic scaling・Scaling・Display reverse・ECO display・Display digits limitation・Sample hold・Peak hold・Bottom hold・Peak to peak hold・Self peak hold・Self bottom hold・Zero reset・Initial reset・ON-delay timer・OFF-delay timer・One-shot timer・Differentiation・Sensitivity selection・Threshold value direct setting・Positioning teaching・2-point teaching・Automatic teaching・Hysteresis width variability・Monitor focus・Non-measuring time setting・(A – B) calculation(Note：The calculation unit is necessary.)・(A + B) calculation(Note：The calculation unit is necessary.)・Mutual interference prevention (Note：The calculation unit is necessary.)・Laser deterioration detection・Key lock・Zero reset memory |
| Nombor Produk | HL-AC1 |
| Voltan bekalan | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
| Input Laser MATI | 0 V connection: Laser emission haltOpen: Laser emission-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Kitaran pengukuran | 150 micro s |
| Tahap pencemaran | 3 (industrial environment) |
| Input tetapan semula sifar | 0 V connection: Zero reset operatesOpen: Zero reset ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Penggunaan semasa | 190 mA or less (when connected to the sensor head) |
| Sambungan kabel I/O | Extension up to total 10 m32.808 ftis possible, with 0.09 mm2or more, cable.(Note) If the extension cable is longer than 10 m32.808 ft, then it will not qualify for CE marking. |
| Paparan sub-digital | 5 digit yellow LED display[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.] |
| Paparan digital utama | 5 digit red LED display[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.] |
| Rintangan penebat | 20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure |
| Kepala sensor yang berkenaan | HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F |
| Ketahanan voltan | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Petunjuk: Dayakan (DAYAKAN) | Green LED (lights up during normal operation) |
| Petunjuk: Output penghakiman | HIGH: Orange LED (lights up when measured value > HIGH threshold value)PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)LOW: Yellow LED (lights up when LOW threshold value > measured value) |
| Petunjuk: Tetapan semula sifar (SIFAR) | Green LED (lights up when the zero reset function is enabled) |
| Kadar persampelan purata yang boleh ditetapkan | 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1). |
| Pematuhan arahan penandaan CE | EMC Directive, RoHS Directive |
| Output penghakiman (TINGGI, LULUS, RENDAH) | NPN open-collector transistor-Maximum sink current: 50 mA-Applied voltage: 30 V DC or less (between judgment output and 0 V)-Residual voltage: 1.2 V or less (at 50 mA sink current) |
| Petunjuk: Pemancaran laser (LD HIDUP) | Green LED (lights up during laser emission) |
| Rintangan alam sekitar: Kelembapan ambien | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Rintangan alam sekitar: Rintangan kejutan | 300 m/s2acceleration (30 G approx.) in X, Y and Z directions three times each |
| Output linear: Ciri-ciri suhu | plus or minus 0.2 % F.S./℃(Note) These are the temperature characteristics of the linear output when the sensor head is connected. |
| Rintangan alam sekitar: Suhu ambien | 0 to +50 ℃+32 to +122 ℉(No dew condensation allowed), Storage: -25 to +65 ℃-13 to +149 ℉ |
| Rintangan alam sekitar: Rintangan getaran | 10 to 150 Hz frequency, 0.7 mm0.028 indouble amplitude in X, Y and Z directions for 80 min. |
| Output penghakiman (TINGGI, LULUS, RENDAH): Operasi output | HIGH: ON when measured value > HIGH threshold valuePASS: ON when HIGH threshold value >= measured value >= LOW threshold valueLOW: ON when LOW threshold value > measured value |
| Output penghakiman (TINGGI, LULUS, RENDAH): Bilangan output | HIGH / PASS / LOW 3 values output |
| Output penghakiman (TINGGI, LULUS, RENDAH): Kategori penggunaan | DC-12 or DC-13 |
| Output penghakiman (TINGGI, LULUS, RENDAH): Perlindungan litar pintas | Incorporated |
Penerangan Produk
HLT1 Series Controller, 12-24 VDC Power, NPN Digital Output, Selectable Analog Output between 4-20mA and ±4V
Ciri-ciri Utama
- Kualiti gred industri
- Patuh RoHS
- Sijil CE
- Jaminan 1 tahun
Dokumen Produk
Lembaran Data
Spesifikasi teknikal dan data prestasi
Manual Pengguna
Panduan pemasangan dan operasi
