

| Parameter | Nilai |
|---|---|
| • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. | |
| Pengekodan | A |
| Dilindungi | yes |
| Jenis kabel | PUR halogen-free black [PUR] |
| Reka bentuk kepala | Pin |
| Nota keselamatan | WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. |
| Jenis sensor | Universal |
| Jenis benang | M12 |
| Panjang kabel | 2 m |
| Berat kabel | 36 kg/km |
| Bebas halogen | in accordance with DIN VDE 0472 part 815 |
| Jenis produk | Circular connectors (device side) |
| Voltan ujian | ≥ 3000 V |
| Gaya UL AWM | 20549 / 10493 (80°C/300 V) |
| Nota perhimpunan | With flat nut |
| Jenis pemasangan | Rear mounting M16 x 1.5 With flat nut |
| Keseluruhan kelainan | 4 wires, twisted |
| Bahan pengedap | FKM |
| Kapasiti kabel | ≤ 80 pF/m (Conductor-Conductor) |
| Impedans gelombang | ≥ 62 Ω (f = 10 MHz) |
| Talian isyarat AWG | 22 |
| Semakan artikel | 10 |
| Bahan sentuh | CuZn |
| Rintangan api | in accordance with UL 758/1581 FT2 |
| Jenis benang kepala | M12 |
| Rintangan lain | Highly resistant to acids, alkaline solutions and solvents |
| Kaedah sambungan | Cable connection |
| Soket kabel kepala | straight |
| Jenis penguncian kepala | SPEEDCON |
| Rintangan terhadap minyak | in accordance with DIN EN 60811-2-1 |
| Tork pengetatan | 3 Nm ... 4 Nm (Installation-side) |
| Bahan konduktor | Bare Cu litz wires |
| Rintangan sentuhan | ≤ 3 mΩ |
| Arus nominal IN | 4 A (Plug/socket in accordance with IEC 61076-2-101, cable technical data is to be observed) |
| Voltan nominal UN | 250 V |
| Nota tentang operasi | The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. |
| Maklumat pesanan: | Lock nut is included in the scope of delivery |
| Wayar tunggal, warna | brown, white, blue, black |
| Hartanah istimewa | Flexible cable conduit capable |
| Tahap pencemaran | 3 |
| Lukisan dimensi | |
| Bilangan jawatan | 4 |
| Voltan lonjakan yang dinilai | 2.5 kV |
| Medium penghantaran | Copper |
| Tahap perlindungan | IP67 (When plugged in) |
| Bilangan soket kabel | 1 |
| Kategori voltan lampau | II |
| Penamaan piawai | M12 connector |
| Rintangan penebat | ≥ 100 MΩ |
| Ketebalan, penebat | ≥ 0.21 mm |
| Sarung luaran, warna | black-gray RAL 7021 |
| Voltan nominal, kabel | ≤ 300 V |
| Sarung luar, bahan | PUR |
| Keratan rentas konduktor | 4x 0.34 mm² (Signal line) |
| Jenis sambungan kenalan | Pin |
| Diameter kabel luaran | 4.95 mm ±0.2 mm |
| Penutup perisai optik | 80 % |
| Ketebalan, sarung luar | approx. 0.50 mm |
| Bahan pembawa sentuh | PA 6.6 |
| Bahan permukaan sentuh | Au |
| Penebat dawai bahan | PP |
| Piawaian/spesifikasi | IEC 61076-2-101 |
| Rintangan konduktor maksimum | max. 58 Ω/km (at 20 °C) |
| Kitaran pemasukan/penarikan balik | > 100 |
| Bahan untuk sambungan skru | Zinc die-cast, nickel-plated |
| Diameter dawai termasuk penebat | 1.27 mm ±0.02 mm (Signal line) |
| Suhu ambien (operasi) | -40 °C ... 80 °C (cable, fixed installation) |
| Talian isyarat struktur konduktor | 42x 0.10 mm |
| Kapasiti beban dinamik (lenturan) | Max. bending cycles: 10000000, Bending radius: 10 x D, Traversing path: 10 m, Traversing rate: 3 m/s, Acceleration: 10 m/s² |
| Penarafan mudah terbakar mengikut UL 94 | V0 |
| Jejari lenturan minimum, pemasangan tetap | 5 x D |
| Jejari lenturan terkecil, pemasangan tetap | 25 mm |
| Jejari lenturan minimum, pemasangan fleksibel | 10 x D |
| Jejari lenturan terkecil, pemasangan boleh alih | 50 mm |
Spesifikasi teknikal dan data prestasi
Panduan pemasangan dan operasi