Dalam Stok Produk Hangat
HC-K 6/12-EBUS
HC-K 6/12-EBUS 1636363 PHOENIX CONTACT Contact insert
$127.97USD
114 dalam stok
Spesifikasi Utama
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Jenis:B16
Lebar:34 mm
Ketinggian:47 mm
Maklumat Pembekal
Produk: 0
Biasanya dihantar dalam 2-3 hari bekerja
Kualiti Dijamin
Penghantaran Pantas
Sokongan Teknikal
Spesifikasi Teknikal
| Parameter | Nilai |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Jenis | B16 |
| Lebar | 34 mm |
| Ketinggian | 47 mm |
| Panjang | 84.1 mm |
| Siri | HC-K |
| Jeneral | For HEAVYCON ADVANCE and HEAVYCON housing of type B16/B32, axial connection for 2 mm Allen wrench |
| Permohonan | Power/signal |
| Jenis produk | Contact insert with a fixed no. of positions |
| Nota perhimpunan | To ensure correct use, installation in housing with IP54 protection or better is required |
| Arus yang dinilai | 40 A (power contacts) |
| Semakan artikel | 04 |
| Diameter sentuhan | 4 mm |
| Bahan sentuh | Cu alloy |
| Penomboran kenalan | 1 - 6 (power contacts) |
| Bilah pemutar skru | 0.5 x 3.5 mm (control contacts) |
| Tork pengetatan | 2 Nm ... 2.5 Nm (PE connection) |
| Profil sambungan | 6+12+PE |
| Tahap pencemaran | 3 |
| Lukisan dimensi | |
| Bilangan jawatan | 18 |
| Voltan lonjakan yang dinilai | 8 kV (power contacts) |
| Kategori voltan lampau | III |
| Teknologi sambungan | Axial screw connection (power contacts) |
| Jenis bahan sentuh | turned |
| Bilangan kenalan kuasa | 6 |
| Voltan yang dinilai (III/3) | 690 V |
| Keratan rentas konduktor | 2.5 mm² ... 10 mm² (power contacts) |
| Bilangan kenalan kawalan | 12 |
| Bahan pembawa sentuh | PC |
| Kitaran pemasukan/penarikan balik | ≥ 500 |
| Keratan rentas sambungan AWG | 12 ... 8 (power contacts) |
| Suhu ambien (operasi) | -40 °C ... 125 °C |
| Jarak lubang gerudi, mendatar | 77.5 mm |
| Voltan yang dinilai untuk kenalan kuasa | 230/400 V |
| Penarafan mudah terbakar mengikut UL 94 | V0 |
| Panjang pelucutan wayar individu | 8 mm +1 mm (Power 6 mm² ... 10 mm²) |
| Bahan permukaan sentuhan, sentuhan kuasa | Ag |
| Bahan permukaan sentuhan, sentuhan kawalan | Ag |
Penerangan Produk
Contact insert, number of poles: 6+12+PE, size: B16, power contacts: 6, control contacts: 12, Female, Axial screw connection, 690 V, 40 A, 2.5 mm² ... 10 mm², application: Power/signal
Ciri-ciri Utama
- Kualiti gred industri
- Patuh RoHS
- Sijil CE
- Jaminan 1 tahun
Dokumen Produk
Lembaran Data
Spesifikasi teknikal dan data prestasi
Manual Pengguna
Panduan pemasangan dan operasi
