Dalam Stok Produk Hangat
HC-HS 2-D7-EBUS
HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert
$35.46USD
326 dalam stok
Spesifikasi Utama
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Jenis:D7
Ujian:DIN VDE 0627/86
Lebar:21 mm
Maklumat Pembekal
Produk: 0
Biasanya dihantar dalam 2-3 hari bekerja
Kualiti Dijamin
Penghantaran Pantas
Sokongan Teknikal
Spesifikasi Teknikal
| Parameter | Nilai |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Jenis | D7 |
| Ujian | DIN VDE 0627/86 |
| Lebar | 21 mm |
| Ketinggian | 34.8 mm |
| Panjang | 21 mm |
| Siri | HC-HS |
| Jeneral | for HC-D7 housing, axial connection 2.0 mm, Allen key |
| Permohonan | Power |
| Jenis produk | Contact insert with a fixed no. of positions |
| Nota perhimpunan | To ensure correct use, installation in housing with IP54 protection or better is required |
| Arus yang dinilai | 40 A |
| Semakan artikel | 04 |
| Diameter sentuhan | 4 mm |
| Bahan sentuh | Copper alloy |
| Soket heksagon | SW2,0 |
| Penomboran kenalan | 1 - 2 |
| Tork pengetatan | 0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing) |
| Profil sambungan | 2+PE |
| Tahap pencemaran | 3 |
| Lukisan dimensi | |
| Bilangan jawatan | 2 |
| Voltan lonjakan yang dinilai | 6 kV |
| Kategori voltan lampau | III |
| Teknologi sambungan | Axial screw connection |
| Jenis bahan sentuh | turned |
| Bilangan kenalan kuasa | 2 |
| Voltan yang dinilai (III/3) | 400 V |
| Keratan rentas konduktor | 4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used) |
| Bahan pembawa sentuh | PC |
| Bahan permukaan sentuh | Ag |
| Kitaran pemasukan/penarikan balik | ≥ 500 |
| Keratan rentas sambungan AWG | 10 ... 8 |
| Suhu ambien (operasi) | -40 °C ... 125 °C (including heating up of contacts) |
| Sambungan dalam akaun dengan standard | IEC / EN |
| Peraturan pembinaan dan pengujian | DIN VDE 0627/86 |
| Penarafan mudah terbakar mengikut UL 94 | V0 |
| Panjang pelucutan wayar individu | 8 mm +1 mm |
Penerangan Produk
Contact insert, number of poles: 2+PE, size: D7, power contacts: 2, Female, Axial screw connection, 400 V, 40 A, 4 mm² ... 10 mm², Application: Power
Ciri-ciri Utama
- Kualiti gred industri
- Patuh RoHS
- Sijil CE
- Jaminan 1 tahun
Dokumen Produk
Lembaran Data
Spesifikasi teknikal dan data prestasi
Manual Pengguna
Panduan pemasangan dan operasi
